U-Bolt Flip Kit??
Have a chance to get a u-bolt flip kit pretty damned cheap...but I have heard that you need to only use it with a high steer kit...any truth to this?? Looked at the front end I really don't see how a...
View Articlenew rear axle shafts
and the fun just never stops. Getting my rig all worked through before I go down to the Rubicon. I was doing some rear brake work and I managed to be a dumb a$$ and tweeked one of the wheel flanges on...
View Article85 Runner Build Up
I'm working on a 1985 4Runner build. I'm going to run 35's on 63 chevys, with the stock rears moved to the front, as well as dropping in a High Steer, 5.29's and an ARB rear. I haven't installed a High...
View ArticleProject Chev Swap
So I finally decided what axles im going with for the SAS. Full width chev half tons dana 44 front, 12 bolt rear, chev 63" springs front and rear.I would go with stronger axles but im never going to...
View ArticleDriveline Shop
Just wrapping up my lift this weekend, and am going to need a pair of much longer drive lines. Anyone have any experience in this, or can anyone suggest a good shop around portland? Thanks.
View ArticleTrekker
Picked up a couple of things for the trekker: for half doors: Now just need to get dual transfer case adapter, planning on converting to 23 spline. So I know Marlin basically invented the dual adapter,...
View ArticleWill it work?
If I bought a 85 Ext PU without an engine. Would a 20r bolt up to the stock 22r tranny?
View Articleshackle lift
I just put on some longer shackles. theyr about twice as long as stock. My 4runner now sits about an 1" too tall, but I'm pretty sure the springs will eventually be back down on the bump stops. It...
View ArticlerevengeRUNNER build up
i am starting the build up of my 95 4runner and will be posting pics as work progresses... until then here is a build sheet to see whats all being done... body: 95 4runner mods to body: roof cut of...
View Articlelong spline drive lines
Who has them? you like them? would you buy them again? I just bought trailgears long spline kit and snapped it on the second rock encounter. i didnt hit it hard or anything just spun the d-line on top...
View Articlelooking for....
hey guys im looking for a front bumper and a 8000 lbs winch for my 2003 taco ...anyone have either
View ArticleCool shop found in Portland
Just thought I'd pass this on as these guys can really be life savors. I've been struggling to get a good double flare on some brake lines for my GM master cylinder conversion. I basically have...
View ArticleThe guy next door's buggie
It isnt mine but at least I can help build it! ] ] ... The guy next door's buggie
View ArticleWTB front/rear bumper
:saw: looking for tube bumpers at a cheap price new or used. no junk. or even just a rear chrome stock bumper. needs to fit 1989 toyota pick up std cab short bed:saw:
View Articleproject takeover
So I have a 3/4 ton chevy and a beat to crap 81 toyota cab, what should I do with them. I am gonna put the chevy running gear in the yota hopefully in time for takeover. The plan: 81 yota cab and front...
View Articlesgt brase's bed cage
building joel's bed cage... still have some supports to weld in and building a basket for the top... cody wants me to paint it pink ... sgt brase's bed cage
View ArticleProject Hillbilly
Alright boys. Since yall have had your projects. Its time for me to start with mine. I picked my 87' 4Runner up for 40 dollars. What the kid didn't tell me when I first talked to him, the rear of it is...
View Article94 Yoter Build Thread 56K BEWARE
This is going to be my official build thread so I think next thing is weld on Sliders and Detroit soft locker and just some other stuff ARB Bull Bar later bigger tires the works SkyJacker 4 inch...
View ArticleNew Box 56k I get picture happy
When I got my truck it came with this Delta Champion Box I loved it through everything in there only thing that made me made were it had these what seemed like battery acid stains is what I think they...
View Articlenew trail rig build done
here is the newest trail rig to roll out of my shop... ... new trail rig build done
View ArticleTrekker has some work done at Revenge Fab
Went down today and picked up the Trekker from Derek. I am really happy with what he came up with for the bumpers. Thanks for the awesome deal!! Front: It doesn't stick out too much like some I have...
View ArticleLooking to get a bumper built- Southern OR
I'm looking to get a tube bumper made for the rear of my 2001 Tacoma. I'm in Coos Bay, and I can't find anyone around here that can do it... I'd be willing to drive a few hours if there's anyone who'd...
View Articlebed bar i made
thought id post it here cause i did most of the work when the weather was not favorable. haha love oregon. this was my first experience notching and actually have to line things up fairly straight....
View ArticleAnyone needing a metal fabricator?
I do side work in metal fabrication, welding, and tube work. Let me know if anyone need something installed and made from scratch. My phone number is 360-936-5400 Thanks
View ArticleProject more leg room
Well, I finally got tired of humping the steering wheel, so heres the remedy to my problem Plans are to put the rears in the front, blazer rears, flatbed, locked rear, open front(for now), 10000 pound...
View Articlelooking to get a bumper built for my '06
wasn't sure if i should post this here or in the classifieds... i am looking to get a bumper built for my '06 taco. i am interested in something similar to the all-pro hybrid. doesn't need to be an...
View Article2in suspension lift?
Just picked up an 84 toy and its stock sitting on 33's... The tires rub when turning and i want to lift it up a little but not sky it. It came with (not installed) 2in rear blocks and some rear leafs...
View Article99 xtracab Taco Work
So it is beginning. I have finally sold my nerf bars and if all goes well i will sell my sub/amp system tonight which will provide just enough money for a 1" body lift and some sliders. I am goign to...
View ArticleAny fabrication shop(s) in Portland that can do plate work (rear bumper)?
Hi, I'm looking to have a rear bumper fabricated for my '00 Taco. I'm not a big fan of the tube bumpers ... I want something more square, like a 'Cruiser bumper. Somthing similar to this:...
View Article06 DC SAS'D DD Expedition rig
I have a thread in the late model section in the main forum but im an Oregonian and I would rather chat with someone that I might atcually wheel with someday and not some punk from who knows were. I...
View ArticleF-toy #58
So I am not sure why I am posting here but oh well. So I picked up a little project Sunday night. I have some big plans. It will more then likely be a few months before I get to actually building this...
View ArticleProject 3.0 slow build suggestions?
I picked up a 1990 v6 runner for cheap.. Blown motor straight body and a future daily driver... Not much cash to drop into it.. Started with a new motor (not yet installed) and a pimpin 2" body lift.
View Article
More Pages to Explore .....